Y175 type disc grinder one, disc grinder Overview: Hebi first Feng instrument 0392-3206887,13603922896, http://www.hbxfyq.com produce disc mill is mainly used for crushing medium hardness ore, metallurgical, geology, building materials, chemical industry laboratory or laboratories in the necessary equipment for material crushing. Two, disc mill structure and performance characteristics: 1, disc grinder mainly by the body, base, spindle, activity disk, fixed disk, cover and hopper, etc., two characteristics: the power to pass through the V-belt pulley driven spindle rotation, so that the activities disk fixed disk relative motion, so that the crushed sample, the particle size by the size of the hand wheel, spindle, etc. to control the granularity adjustment disc space purposes. Body, cover, cover composed of a studio, the studio for the crushed material, the feed material from the mouth to join the top cover into the two intermediate disc, the compression sample pulverized sample after crushing disc from both out of the middle of the gap. Fall below the hopper. The principle of adjusting mechanism, release large hand wheel, rotate the small hand wheel, turn the adjusting screw spindle push to make the activity tray forward or backward. Thereby adjusting the gap of the two disc, to adjust the purpose of the material grain. Third, the main technical parameters of a disc grinder, model: Y175 type 2, disc diameter: 150 mm 3, feeding ≤ 3 mm 4-maximum size, the particle size :1-0.15 mm 5, Productivity: 25 kg / hr 6 , Spindle speed: 780 r / min 7, Motor Type: Y909-4 8, speed: 1400 r / min 9, motor power: 1.1 kilowatts 1, Model: Y200 type 2, disc diameter: 150 mm 3, the maximum feed size ≤ 6 mm 4-, the particle size: 0.2 mm 5, Productivity: 60 kg / hour 6, motor power: 2.2 kilowatts 1, Model: Y250 type 2, disc diameter: 250 mm 3, the maximum feed particle size ≤ 8 mm 4-, the particle size: 0.3 mm 5, Productivity: 80 kg / hour 6, motor power: 3 kilowatts four, disc grinder using procedures 1, shredders should be placed on a stable platform 2, open the grinding chamber cover, will crushed material into the crushing chamber, then cover screw is good. 3, turn on the switch, the device begins to work, about 2 minutes, turn the switch off, open the cover removed crushed, if not reach the fineness of the crushed material requirements reboot. 4, an amount not to exceed the requirements crushed to avoid motor overheating caused by excessive load is affecting life. Crushed material must be kept dry, not wet grinding or high fat items. 5, each grinding time is less than 5 minutes, intermittent 3 minutes, then continue to use. 6, replacement blades, carbon brushes should pay attention must be cut off and tighten the wire gong, and always check for loose parts. 7, crushing chamber to open the front cover must be cut off should be noted, is strictly prohibited openings start. 8, should be crushed in a timely manner after use clean, dry clean. Five, disc grinder use the machine as a whole packing, unpacking after moving to the appropriate location, place a smooth, power, you can try. Should be checked before use transmission parts for loose parts and other irregularities, the machine running direction of the arrow should be the same. When you first load test 1-2 minutes, until no abnormal phenomenon was observed before feeding, feed should be gradually increasing the amount of logistics and always observe the power supply and motor functioning, to be feeding the power balance is operating normally, surely die cutting gate, to work. Way as a result of the material is too moist, too sticky end, the impact of the powder, the material should be dried or replaced coarse sieve. Simply replace the front cover open sieve can be carried out, the installation should pay attention to both sides of the front cover handwheel elastic consistency, ensure that the front cover and the chassis seal. Parking should stop feeding, let the machine run 5-20 minutes and then stop. In order to reduce the residual material. Six, disc grinder regularly check bearing maintenance and repairs, replacement of high-speed butter, in order to ensure the normal operation of the machine, should always check the wearing parts, if worn serious phenomenon must be promptly replaced. Found when using the machine spindle speed gradually receded, the motor must be adjusted downward, so that the machine can achieve the required speed, abnormal should stop check. Non-metallic materials inflow boot inside the machine, such as nails, iron and so on. After work, the various parts of the machine should be cleaned residual materials, deactivate longer must wipe the machine with a tarpaulin cover is good. Service: installation, commissioning and on-site training: according to user requirements of the time and place for the user free installation equipment. The user provides free on-site operator training services, allowing users to be able to master the instrument performance, operation and general maintenance. Warranty provisions: supply according to national standards, the whole year warranty (except wearing parts) product life-long maintenance. Maintenance requirements: In normal use, the instrument if the failure, repair station after receiving the notice guaranteed response within 24 hours, for on-site maintenance, we are committed to reach the scene and sent as soon as possible in the shortest time troubleshooting. Replacement parts costs and labor rate prescribed by the company uniform price charged. Hebi City first fung Instrument Co., Ltd. 0392-3206887 / 0392-3216726 / 13603922896 transport: Rail transport or logistics delivery now: Spot Packing: Wooden